Instrument panel center support bracket. Instrument panel ash receiver

Instrument panel center support bracket

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.

REMOVAL

(1) Disconnect and isolate the battery negative cable.

(2) Pull the floor carpet back from the front of the floor panel transmission tunnel far enough to access the center support bracket mounting screws.

(3) Remove the two screws that secure the center support bracket to the instrument panel.

(4) Remove the two screws on the left, and one screw on the right that secure the instrument panel center support bracket to the Airbag Control Module (ACM) bracket on the floor panel transmission tunnel (Fig. 12).

Fig. 12 Instrument Panel Center Support Bracket Remove/Install Fig. 12 Instrument Panel Center Support Bracket Remove/Install

1 - CENTER SUPPORT BRACKET

2 - SCREW

3 - AIRBAG CONTROL MODULE BRACKET

(5) Remove the center support bracket from the instrument panel.

INSTALLATION

(1) Position the center support bracket to the ACM bracket on the floor panel transmission tunnel.

(2) Install and tighten the two screws on the left, and one screw on the right that secure the instrument panel center support bracket to the Airbag Control Module (ACM) bracket on the floor panel transmission tunnel. Tighten the screws to 11.8 N*m (105 in. lbs.).

(3) Align the screw holes in the instrument panel to the mounting holes in the center support bracket.

(4) Install and tighten the two screws that secure the center support bracket to the instrument panel.

Tighten the screws to 11.8 N*m (105 in. lbs.).

(5) Reposition the floor carpet on the front of the floor panel transmission tunnel to conceal the instrument panel center support bracket.

(6) Reconnect the battery negative cable.

Instrument panel ash receiver

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.

REMOVAL

(1) Disconnect and isolate the battery negative cable.

(2) Open the instrument panel ash receiver.

(3) Depress the spring retainer in the center of the open ash receiver to release it, then lift the ash receiver slightly and pull it straight out from the pivot pins in the instrument panel lower bezel.

(4) Remove the two screws that secure the ash receiver flame shield to the instrument panel lower bezel (Fig. 13).

(5) Pull the ash receiver flame shield out from the instrument panel far enough to disengage the two retaining tabs on the top of the shield from the mounting holes in the instrument panel lower bezel.

(6) Lower the flame shield from the instrument panel lower bezel far enough to access the ash receiver lamp and hood.

(7) Squeeze the ash receiver lamp and hood bracket to disengage the unit from the mounting hole in the flame shield.

(8) Remove the ash receiver flame shield from the instrument panel lower bezel.

Fig. 13 Instrument Panel Ash Receiver Remove/ Install Fig. 13 Instrument Panel Ash Receiver Remove/ Install

1 - INSTRUMENT PANEL LOWER BEZEL

2 - ASH RECEIVER

3 - SCREW

4 - FLAME SHIELD

INSTALLATION

(1) Position the ash receiver flame shield to the instrument panel lower bezel.

(2) Squeeze the ash receiver lamp and hood bracket and engage the unit to the mounting hole in the flame shield.

(3) Insert the two retaining tabs on the top of the ash receiver flame shield into the mounting holes in the instrument panel lower bezel, then push the shield forward to engage the tabs with the bezel.

(4) Install and tighten the two screws that secure the ash receiver flame shield to the instrument panel lower bezel. Tighten the screws to 2.2 N*m (20 in.

lbs.).

(5) Align the pivot receptacles on each side of the ash receiver with the pivot pins in the instrument panel lower bezel.

(6) Push the ash receiver forward onto the pivot pins in the instrument panel lower bezel until the spring retainer in the center of the open ash receiver snaps into place.

(7) Reconnect the battery negative cable.

    Dodge Durango (DN) 1998-2003 Service Manual

    Categories


    © 2017-2024 Copyright www.dodurango.net