Toyota
Dodge Durango
 Service Manual
Heating and Air Conditioning » Removal and installation
Blower motor resistor

FRONT

REMOVAL

(1) Disconnect and isolate the battery negative cable.

(2) Remove the cowl plenum cover/grille panel from the cowl top. See Vacuum Reservoir in the Removal and Installation section of this group for the procedures.

(3) Reach through the cowl plenum access hole (Fig. 21) to remove the two hex screws that secure the front blower motor resistor to the cowl plenum panel.

Fig. 21 Blower Motor Resistor Remove/Install Fig. 21 Blower Motor Resistor Remove/Install

1 - WINDSHIELD

2 - RIGHT WIPER PIVOT

3 - COWL PLENUM ACCESS HOLE

(4) Pull the front blower motor resistor and its wire harness out of the plenum panel and through the cowl plenum access hole far enough to access the wire harness connector.

(5) Unplug the front blower motor resistor from the wire harness connector.

(6) Remove the front blower motor resistor from the cowl plenum.

INSTALLATION

(1) Plug the front blower motor resistor into the wire harness connector.

(2) Install the front blower motor resistor to the cowl plenum panel by feeding the resistor and wire harness back through the cowl plenum access hole.

(3) Install and tighten the two screws that secure the front blower motor resistor to the cowl plenum panel. Tighten the mounting screws to 2.2 N*m (20 in. lbs.).

(4) Reinstall the cowl plenum cover/grille panel to the cowl top. See Vacuum Reservoir in the Removal and Installation section of this group for the procedures.

(5) Connect the battery negative cable.

REAR

The rear blower motor resistor is used only on models with the optional rear overhead A/C unit.

REMOVAL

(1) Disconnect and isolate the battery negative cable.

(2) Remove the headliner from the passenger compartment of the vehicle. Refer to Group 23 - Body for the procedures.

(3) Disconnect the B-pillar drain hoses from the wye fittings on each side of the rear overhead A/C unit (Fig. 22).

Fig. 22 Rear Overhead A/C Drain Hose Remove/ Install Fig. 22 Rear Overhead A/C Drain Hose Remove/ Install

1 - REAR OVERHEAD A/C UNIT

2 - WYE FITTING

3 - CLIP

4 - GROMMET

5 - DRAIN HOSE

(4) Remove the nine screws that secure the lower housing cover to the rear overhead A/C unit.

(5) Release the lower housing cover snap retainer near the center of the outlet side (rear) of the rear overhead A/C unit (Fig. 23).

Fig. 23 Rear Overhead A/C Unit Lower Housing Cover Remove/Install Fig. 23 Rear Overhead A/C Unit Lower Housing Cover Remove/Install

1 - REAR OVERHEAD A/C UNIT LOWER HOUSING COVER

2 - SNAP RETAINER

3 - OUTLET SIDE

4 - BLOWER MOTOR SWITCH WIRE HARNESS CONNECTOR

5 - INLET SIDE

6 - DRAIN HOSES

(6) Feed the rear blower motor switch wire harness and connector through the hole in the right end of the rear overhead A/C unit lower housing cover while removing the cover from the unit.

(7) Disengage the rear blower motor resistor wire harness connector retainer from the mounting hole in the right rear corner of the rear overhead A/C unit upper housing cover (Fig. 24).

Fig. 24 Rear Blower Motor Resistor Remove/Install Fig. 24 Rear Blower Motor Resistor Remove/Install

1 - WIRE HARNESS CONNECTOR

2 - RETAINER

3 - MOUNTING HOLE

4 - RESISTOR

5 - SCREW

(8) Unplug the rear blower motor resistor wire harness connector.

(9) Remove the screw that secures the rear blower motor resistor bracket to the rear overhead A/C unit upper housing cover.

(10) Remove the rear blower motor resistor and bracket as a unit from the rear overhead A/C unit.

INSTALLATION

(1) Position the rear blower motor resistor and bracket in the right rear corner of the rear overhead A/C unit upper housing cover and secure it with the mounting screw. Tighten the mounting screw to 2.2 N*m (20 in. lbs.).

(2) Plug in the rear blower motor resistor wire harness connector.

(3) Engage the rear blower motor resistor wire harness connector retainer to the mounting hole in the right rear corner of the rear overhead A/C unit upper housing cover.

(4) Feed the rear blower motor switch wire harness and connector through the hole in the right end of the rear overhead A/C unit lower housing cover while positioning the cover to the unit.

(5) Be certain that the lower housing cover snap retainer near the center of the outlet side (rear) of the rear overhead A/C unit is engaged.

(6) Install the nine screws that secure the lower housing cover to the rear overhead A/C unit. Tighten the mounting screws to 2.2 N*m (20 in. lbs.).

(7) Connect the B-pillar drain hoses to the wye fittings on each side of the rear overhead A/C unit.

(8) Reinstall the headliner to the passenger compartment of the vehicle. Refer to Group 23 - Body for the procedures.

(9) Connect the battery negative cable.

    More about «Removal and installation»:

    Service warnings and precautions

    B-pillar refrigerant line

    Blower motor

    Blower motor relay

    Blower motor resistor

    Compressor

    Compressor clutch

    Compressor clutch relay

    Condenser

    Ducts and outlets

    Electronic cycling clutch switch

    Evaporator coil

    Expansion valve

    Filter-drier

    Heater-a/c control

    Heater-a/c housing

    Heater-a/c housing door

    Heater core

    High pressure cut-off switch

    Liquid line

    Low pressure cut-off switch

    Mode door vacuum actuator

    Rear blower motor switch

    Rear overhead a/c unit

    Refrigerant line coupler

    Suction and discharge line

    Suction line jumper

    Temperature control cable

    Underbody refrigerant line

    Vacuum check valve

    Vacuum reservoir

    Dodge Durango Service Manual / Heating and Air Conditioning / Removal and installation / Blower motor resistor

    Dodge Durango Service Manual

    Categories


    © 2017-2019 Copyright www.dodurango.net
    0.0049